1 Item(s) Added to Cart
View CartD2A01RU4
New
1. Cold laminator : Maximum Laminating Width: 63.8"
2. Maximum Laminating Thickness: 1"(28mm)
2. Maximum Laminating Speed: 39.4 ft/min
4. Heating Method for the fully auto roll laminator: Cold & Hot
5. Display for the roll laminator: Digital
6. Roller Lifting Method: Pneumatic Lifting
This cold laminator can finish wide format graphics up to 63.8", and max laminating speed is 39.3"/min ( 12m/min)
This Laminator equipped with 4 trimmers with micro-adjust structure to ensure accurate cutting position.
TThe clip guard: Infrared ray of safety deflector device which makes sure the safety of the operator.
There are buttons and switches on front control panel or back of the machine for easy operation.
Product Detail:
1. Top and bottom rollers
The top and bottom rollers are one of the most important parts of the laminating machine which are made of silicon rubber. Silicon rubber has the characteristics of high temperature resistance, wear resistance, corrosion resistance and non-sticky.
2. Drawing axis, film axis, paper axis and finished product axis
The four mandrels are composed of aluminium rods, aluminum heads, bearings, rubber strips and other components. The outer diameter is controlled within 3 inches which facilitates the loading and unloading of conventional film products on the market, such as yellow film, laminating film and so on.
3. Pneumatica switch and cylinder
The pneumatic switch has upper, middle and lower 3 modes. In the case of air in the equipment, the top roller can be lifted up, the top roller can be lowered down, and the middle gear can temporarily lock the air inflow and output. The cylinder type of this equipment is SDA50-30, which makes the lifting height of the top roller more than 28mm (1.1").
4. Emergency stop switch
When the machine is in and emergency or dangerous state, the power supply can be cut off by the emergency switch and the equipment can be stopped to protect the safety of the person and equipment.
5. Cutters
The use of the cutting knife can make it possible to cut vertically and white edges at the same time in the process of laminating.
6.Tighten your grip
The tightening handle is mainly used to adjust the tightening force of four mandrels. Before leaving the factory, the four handles have been debugged accordingly. Users can use them directly. The tightening force is increased by twisting clockwise; the tightening force is reduced by twisting counterclockwise.
7. Simple control panel
Working Sketch Map
Applications:
This laminator with heat-assisted can be widely used for pre-masking vinyl graphicm mount prints on the substrate, over laminating inkjet prints and so on. The cold laminator is used for after printing. Widely applied for photographic, Ad. shop and copy shop to do lamination work, adding a protective layer on book cover, photographic, color pages, documents, charts, drawings, indoor advertising products, etc.
8. Operation Manual
SPECS | |
Model | LP1700-S3 |
Max. Laminating Width | 63.8" |
Max. Laminating thickness | 1" |
Laminating Speed | 39.4 ft/min |
Top Roller Diameter | 5.12" |
Bottom Roller Diameter | 4.3" |
Heating Method | Infrared Heating |
Heating Temperature | Room- 176 "F |
Roller Lifting Method | Pneumatic Lifting |
Rated Input Voltage | 110V/60Hz |
Continuous Power | 2000W |
Trimmer Quantity | 4 |
N.W. | 331Lbs |
G.W. | 441Lbs |
Packaging Size | 84.65x31.5 X 28.7 inch |
Package Included: | |
Host | 1 Unit |
Drawing mandrel left brakcet | 1 Piece |
Drawing mandrel right bracket | 1 Piece |
Frame foot | 2 Pieces (left and right) |
Square Tube | 2 Pieces |
Foot switch | 1 Piece |
Heat glass Tube | 2 Pieces (only need one installation to prevent damage during transportation) |
Drawing mandrel | 1 Piece |
Oil-water separator | 1 Set |
Screw and tool pack | 1 Set |
Manual | 1 Set |